675 IAC 31-2-11 Standard for passenger tramways-aerial tramways and lifts, surface lifts, and tows

Sec. 11. (a) That certain document being titled the American National Standard for Passenger Ropeways-Aerial Tramways, Aerial Lifts, Surface Lifts, Tows and Conveyors - Safety Requirements, 2006 edition (ANSI B77.1, 2006), published by the American National Standards Institute, 25 West 43rd Street, New York, NY 10036, be and the same is hereby adopted by reference as if fully set out in this article, save and except those revisions made in this section. (b) Delete subsection 1.3 in its entirety. (c) In subsection 1.4, "Authority having jurisdiction" means the division. (d) Delete section 8 in its entirety and substitute the following: 8. Referenced Standards. When any of the following standards are referenced within this standard (ANSI B77.1, 2006), they shall not be considered as adopted by reference but rather shall be treated as nationally accepted practices in accordance with this section for guidance only and are not enforceable. 8.1 Adopted Rules of the Regulated Amusement Device Safety Board 8.1.1 Whenever reference is made to American National Standard Flammable and Combustible Liquids Code, NFPA 30 within this standard (ANSI B77.1, 2006), the reference is deleted and the Indiana Fire Code (675 IAC 22), a rule of the Indiana fire prevention and building safety commission, is substituted therefor. 8.1.2 Whenever reference is made to American National Standard for Storage and Handling of Liquefied Petroleum Gases, NFPA 58 within this standard (ANSI B77.1, 2006), the reference is deleted and 675 IAC 28-1-22, a rule of the Indiana fire prevention and building safety commission, is substituted therefor. 8.1.3 Whenever reference is made to National Fire Protection Association National Electrical Code, NFPA 70 within this standard (ANSI B77.1, 2006), the reference is deleted and the Indiana Electrical Code (675 IAC 17), a rule of the Indiana fire prevention and building safety commission, is substituted therefor. 8.2 Nationally Accepted Practice 8.2.1 Whenever reference is made to any of the following standards within this standard (ANSI B77.1, 2006), it shall be considered only as a nationally accepted practice: American National Standard Safety Standard for Mechanical Power Transmission Apparatus, ANSI B15.1 American National Standard National Electric Safety Code, ANSI C2 American National Standard for Wire Rope Mines, ANSI M11.1 American National Standard for Stationary Combustion Engines and Gas Turbines, ANSI/NFPA 37 American National Standard Lighting Protection Code, ANSI/NFPA 78 American Gear Manufacturers Association AGMA Surface Durability (Pitting) of Spur Gear Teeth, AGMA 210.02 AGMA Surface Durability (Pitting) Formulas for Straight Bevel and Zerol Bevel Gear Teeth, AGMA 210.02 AGMA Information Sheet for Surface Durability (Pitting) of Spur, Helical, Herringbone and Bevel Gear Teeth, AGMA 215.01 AGMA Design Practice Rating for Surface Durability of Spiral Bevel Gears for Enclosed Drives, AGMA 216.01A AGMA Rating the Strength of Spur Gear Teeth, AGMA 220.02 AGMA Rating the Strength of Helical and Herringbone Gear Teeth, AGMA 221.02 AGMA Rating the Strength of Straight Bevel and Zerol Bevel Gear Teeth, AGMA 222.02 AGMA Rating the Strength of Spiral Bevel Gears for Enclosed Drives, AGMA 223.01A AGMA Practice of Enclosed Speed Reducers or Increases Using Spur, Helical, Herringbone and Spiral Bevel Gears, AGMA 420.04 AGMA Practice for Gearmotors Using Spur, Helical, Herringbone and Spiral Bevel Gears, AGMA 460.05 AGMA Practice for Spur, Helical and Herringbone Gear Shaft-Mounted Speed Reducers, AGMA 480.06 American Petroleum Institute API-RP9B (e) Notwithstanding language to the contrary in the primarily incorporated documents, the version of all secondarily incorporated documents, which are documents referred to in the primarily incorporated documents, shall be the version in effect on September 24, 2009.