WAC 51-11C-40215. Section C402.1.5 — Component performance alternative

C402.1.5 Component performance alternative. Building envelope values and fenestration areas determined in accordance with Equation 4-2 shall be permitted in lieu of compliance with the U -factors and F -factors in Table C402.1.4 and C402.4 and the maximum allowable fenestration areas in Section C402.4.1. For buildings with more than one space conditioning category , component performance compliance shall be demonstrated separately for each space conditioning category. Interior partition ceilings, walls, fenestration and floors that separate space conditioning areas shall be applied to the component performance calculations for the space conditioning category with the highest level of space conditioning. Equation 4-2 Proposed Total UA ≤ Allowable Total UA Where: Proposed Total UA = UA-glaz-prop + UA sky-prop + UA-opaque-prop + FL-slab-prop Allowable Total UA = UA-glaz-allow + UA-glaz-excess + UA sky-allow + UA-sky-excess + UA-opaque-allow + FL-slab-allow UA-glaz-prop = Sum of (proposed U -value x proposed area) for each distinct vertical fenestration type, up to code maximum area UA-sky-prop = Sum of (proposed U -value x proposed area) for each distinct skylight type, up to the code maximum area UA-opaque-prop = Sum of (proposed U -value x proposed area) for each distinct opaque thermal envelope type FL-slab-prop = Sum of (proposed F -value x proposed length) for each distinct slab on grade perimeter assembly UA-glaz-allow = Sum of (code maximum vertical fenestration U -value from Table C402.4, or Section C402.4.1.1.2 if applicable, x proposed area) for each distinct vertical fenestration type, not to exceed the code maximum area 1 UA-glaz-excess = U -value for the proposed wall type from Table C402.4 2 x vertical fenestration area in excess of the code maximum area UA-sky-allow = Sum of (code maximum skylight U -value from Table C402.4 x proposed area) for each distinct skylight type proposed, not to exceed the code maximum area UA-sky-excess = U -value for the proposed roof type from Table C402.4 3 x skylight area in excess of the code maximum area UA-opaque-allow = Code maximum opaque envelope U -value from Table C402.1.4 for each opaque door, wall, roof, and floor assembly x proposed area FL-slab-allow = Code maximum F -value for each slab-on-grade perimeter assembly x proposed length Proposed Total UA ≤ Allowable Total UA Where: Proposed Total UA = UA-glaz-prop + UA sky-prop + UA-opaque-prop + FL-slab-prop Allowable Total UA = UA-glaz-allow + UA-glaz-excess + UA sky-allow + UA-sky-excess + UA-opaque-allow + FL-slab-allow UA-glaz-prop = Sum of (proposed U -value x proposed area) for each distinct vertical fenestration type, up to code maximum area UA-sky-prop = Sum of (proposed U -value x proposed area) for each distinct skylight type, up to the code maximum area UA-opaque-prop = Sum of (proposed U -value x proposed area) for each distinct opaque thermal envelope type FL-slab-prop = Sum of (proposed F -value x proposed length) for each distinct slab on grade perimeter assembly UA-glaz-allow = Sum of (code maximum vertical fenestration U -value from Table C402.4, or Section C402.4.1.1.2 if applicable, x proposed area) for each distinct vertical fenestration type, not to exceed the code maximum area 1 UA-glaz-excess = U -value for the proposed wall type from Table C402.4 2 x vertical fenestration area in excess of the code maximum area UA-sky-allow = Sum of (code maximum skylight U -value from Table C402.4 x proposed area) for each distinct skylight type proposed, not to exceed the code maximum area UA-sky-excess = U -value for the proposed roof type from Table C402.4 3 x skylight area in excess of the code maximum area UA-opaque-allow = Code maximum opaque envelope U -value from Table C402.1.4 for each opaque door, wall, roof, and floor assembly x proposed area FL-slab-allow = Code maximum F -value for each slab-on-grade perimeter assembly x proposed length Notes: 1 Where multiple vertical fenestration types are proposed and the code maximum area is exceeded, the U -value shall be the average Table C402.1.4 U -value weighted by the proposed vertical fenestration area of each type. 2 Where multiple wall types are proposed the U -value shall be the average Table C402.1.4 U -value weighted by the proposed above grade wall area of each type. 3 Where multiple roof types are proposed the U -value shall be the average Table C402.1.4 U -value weighted by the proposed roof area of each type. Notes: 1 Where multiple vertical fenestration types are proposed and the code maximum area is exceeded, the U -value shall be the average Table C402.1.4 U -value weighted by the proposed vertical fenestration area of each type. 2 Where multiple wall types are proposed the U -value shall be the average Table C402.1.4 U -value weighted by the proposed above grade wall area of each type. 3 Where multiple roof types are proposed the U -value shall be the average Table C402.1.4 U -value weighted by the proposed roof area of each type. C402.1.5.1 Component U -factors and F -factors. The U -factors and F -factors for typical construction assemblies are included in Chapter 3 and Appendix A. These values shall be used for all calculations. Where proposed construction assemblies are not represented in Chapter 3 or Appendix A, values shall be calculated in accordance with the ASHRAE Handbook — Fundamentals , using the framing factors listed in Appendix A. For envelope assemblies containing metal framing, the U -factor shall be determined by one of the following methods: 1. Results of laboratory measurements according to acceptable methods of test. 2. ASHRAE Handbook — Fundamentals where the metal framing is bonded on one or both sides to a metal skin or covering. 3. The zone method as provided in ASHRAE Handbook — Fundamentals . 4. Effective framing/cavity R -values as provided in Appendix A. When return air ceiling plenums are employed, the roof/ceiling assembly shall: a. For thermal transmittance purposes, not include the ceiling proper nor the plenum space as part of the assembly; and b. For gross area purposes, be based upon the interior face of the upper plenum surface. 5. Tables in ASHRAE 90.1 Normative Appendix A. 6. Calculation method for steel-framed walls in accordance with Section C402.1.4.1 and Table C402.1.4.1. C402.1.5.2 SHGC rate calculations. Fenestration SHGC values for individual components and/or fenestration are permitted to exceed the SHGC values in Table C402.4 and/or the maximum allowable fenestration areas in Section C402.4.1 where the proposed total SHGCxA less than the allowable total SHGCxA as determined by Equation 4-3. Equation 4-3 — SHGC Rate Calculations Proposed Total SHGCxA ≤ Allowable Total SHGCxA Where: Proposed Total SHGCxA = SHGCxA-glaz-prop + SHGCxA-sky-prop Allowable Total SHGCxA = SHGCxA-glaz-allow + SHGCxA-sky-allow SHGCxA-glaz-prop = Sum of (proposed SHGCx proposed area) for each distinct vertical fenestration type SHGCxA-sky-prop = Sum of (proposed SHGCx proposed area) for each distinct skylight type SHGCxA-glaz-allow = Sum of (code maximum vertical fenestration SHGC from Table C402.4, or Section C402.4.1.3 if applicable, x proposed area) for each distinct vertical fenestration type, not to exceed the code maximum area SHGCxA-sky-allow = Sum of (code maximum skylight SHGC from Table C402.4x proposed area) for each distinct skylight type, not to exceed the code maximum area Proposed Total SHGCxA ≤ Allowable Total SHGCxA Where: Proposed Total SHGCxA = SHGCxA-glaz-prop + SHGCxA-sky-prop Allowable Total SHGCxA = SHGCxA-glaz-allow + SHGCxA-sky-allow SHGCxA-glaz-prop = Sum of (proposed SHGCx proposed area) for each distinct vertical fenestration type SHGCxA-sky-prop = Sum of (proposed SHGCx proposed area) for each distinct skylight type SHGCxA-glaz-allow = Sum of (code maximum vertical fenestration SHGC from Table C402.4, or Section C402.4.1.3 if applicable, x proposed area) for each distinct vertical fenestration type, not to exceed the code maximum area SHGCxA-sky-allow = Sum of (code maximum skylight SHGC from Table C402.4x proposed area) for each distinct skylight type, not to exceed the code maximum area If the proposed vertical fenestration area does not exceed the Vertical Fenestration Area allowed, the target area for each vertical fenestration type shall equal the proposed area. If the proposed vertical fenestration area exceeds the Vertical Fenestration Area allowed, the target area of each vertical fenestration element shall be reduced in the base envelope design by the same percentage and the net area of each above-grade wall type increased proportionately by the same percentage so that the total vertical fenestration area is exactly equal to the Vertical Fenestration Area allowed. If the proposed skylight area does not exceed the Allowable Skylight Area from Section C402.4.1, the target area shall equal the proposed area. If the proposed skylight area exceeds the Allowable Skylight Area from Section C402.4.1, the area of each skylight element shall be reduced in the base envelope design by the same percentage and the net area of each roof type increased proportionately by the same percentage so that the total skylight area is exactly equal to the allowed percentage per Section C402.3.1 of the gross roof area.